Custom 10*7cm Vinyl Carbon Fiber Window Cleaning Wash Car Scraper With Felt Squeegee Tool Film

Short Description:

 

1. A felt-wrapped edge that protects the film, not just the surface under it.

Every scratch on a freshly installed vinyl wrap or window tint costs you a reprint, a re-cut, or an entire panel — and almost all of them come from the tool, not the installer. This squeegee wraps its working edge in a dense, soft fabric felt that rides across the film instead of dragging on it, so the blade glides over gloss, satin, matte, chrome-delete and textured finishes without leaving hairlines, burnishing the adhesive, or scuffing the clear coat underneath. The felt also absorbs the fine grit that inevitably finds its way onto a panel during installation, trapping it in the fibres rather than letting it travel across the surface. For anyone working on customer vehicles, that single detail is the difference between a job that comes back and a job that gets referred.

2. A rigid spine with twin raised grip rails for controlled, one-handed pressure.

Bubble removal is a pressure-control problem, and soft, flimsy scrapers give you no repeatable control — they bow in the middle, skate sideways on wet slip solution, and force you to press harder than the film wants. This tool is moulded from a rigid engineering-grade plastic with two raised rails running the length of the body, which lock your thumb and fingers into a consistent position and stop the squeegee from twisting mid-stroke. The result is even, predictable pressure from the first pass to the hundredth, less hand fatigue on large panels, and the ability to work one-handed while your other hand manages the film. Shorter, more deliberate strokes, fewer returns to the same area, and a cleaner finish in less time.

3. A true 4-inch working edge sized for real installation work.

At roughly 100 × 70 mm, the blade is wide enough to clear a full window or a wrap panel in a sensible number of overlapping passes, yet narrow enough to get into the places that actually cause trouble — door edges, mirror recesses, wheel-arch returns, bumper corners, and the tight radius where film wants to lift. The straight, hard edge gives you a defined contact line so you can feel exactly where the air and slip solution are being pushed, and the felt extends slightly past the plastic so the corners never dig in. Working in overlapping bands, edge to edge, you can drive trapped air and fluid out to the nearest open edge in a single direction rather than chasing pockets around the panel.

4. One tool across vinyl wrap, window tint, PPF, decals, signage and wallpaper.

Most installers end up carrying three or four scrapers because each material behaves differently. This one covers the whole range: cast and calendered vinyl wrap, automotive window film and security film, paint protection film where a soft edge is non-negotiable, adhesive decals, stickers and lettering, digital print and sign-making substrates, and even vinyl wallpaper and frosted privacy film on flat glass. Because the felt edge is what contacts the material, the same stroke technique works on all of them — you are not re-learning your hand position between jobs. For a shop, that means one SKU on the bench instead of a drawer full of half-used tools, and for a home installer it means not buying a “kit” to do a single afternoon’s work.

5. Built to be used daily, sold in packs, and branded for your business.

The body is abrasion-resistant and unaffected by the slip solutions, IPA mixes and adhesive removers that installation work throws at it, and it rinses clean in seconds — no swelling, no softening, no gummed-up edge that starts dragging after a week. In practice it survives hundreds of jobs, which is why it is bought in tens and twenties by tint shops, wrap studios and sign fabricators rather than one at a time. We supply it in single units, 5-packs, 10-packs and bulk cartons, with optional custom logo and colour moulding for distributors, tool brands and training academies who want their name on the bench. Low cost per job, low replacement rate, and a tool your installers will actually reach for.

 


Product Detail

Contact US

 

Rolking Felt

· Since 1983 · OEM / ODM

A vinyl squeegee with a felt edge — 10 × 7.3 cm that will not scratch the film

A plastic card wrapped in black felt. The felt holds the slip solution, wicks grit away from the film, and glides over vinyl, paint protection film, window film and wallpaper without a scratch or a residue line. Four colours, your logo, 1,000 pcs.

10 × 7.3 cm
Felt edge
4 colours
Custom logo
Reusable

MOQ 1,000 pcs · logo printed on the card · FOB / CIF / DDP · Tianjin (Xingang) · pre-production sample before mass production

1983Factory since
1,000Pcs MOQ
4Colours in the mould
FOB·CIF·DDPDelivery terms

Why the edge decides the job

A bare plastic card leaves marks. That is the whole problem.

Installers do not replace a squeegee because the plastic wore out — they replace it because the edge started dragging something across the film. Three failures, one fix.

01

The edge picks up grit and drags it

One grain of sand under a hard plastic corner is a scratch across a bonnet that has to be re-wrapped. On a black car it shows before the customer leaves the bay.

The fixA felt wrap gives a soft, slightly yielding edge — grit is carried in the fibre instead of being pressed into the film.
02

Solution escapes ahead of the blade

Hard edges push the slip solution forward and trap it as bubbles at the end of every stroke, so the same area gets worked twice.

The fixFelt holds solution at the edge, keeps it damp through the stroke and lets air leave sideways instead of under the film.
03

A wet glove slides on a wet card

Install bays are wet by definition. A slick card rotates in the hand mid-stroke and the pressure line goes somewhere you did not plan.

The fixTwo raised ribs moulded into the back give the thumb something to lock against, even through a wet glove.

Hand pressing the felt-edge squeegee across a wet frosted glass panel

Wet work · felt spread

01 — The edge

Ten centimetres of felt is the whole tool.

The body is a moulded plastic card; the felt is what makes it an installation tool rather than a scraper. It is bonded along one long edge, sits flush with the corner radius, and stays flat as it wears. A squeegee is normally described by its blade — and in signwriting the blade is often a bare plastic card about the size of a credit card, which is exactly the tool this felt edge was developed to improve on.

  • ABlack felt wrapBonded, not stapled — no metal to catch on the film and no line of adhesive to smear.
  • BRaised grip ribsTwo moulded lines across the back; the thumb sits between them and the card stops rotating.
  • CCard formatRoughly a credit card in the hand, so it reaches a door gap, a mirror base and a wheel arch edge.

Felt squeegee shown working on a windscreen, side glass, painted door edge and carbon fibre panel

Four surfaces · one edge

02 — Applications

One card, four trades.

It was designed for vinyl, and it is sold into four aisles. The same felt edge that protects a wrap also lifts foam off a windscreen without leaving a wet line, and smooths wallpaper without burnishing the paper.

  • ACar wrap & PPFChases air from under cast vinyl and paint protection film on flat and single-curve panels.
  • BWindow filmPushes the slip solution out to the edge in one direction instead of trapping it mid-pane — the same routine a window film installer already runs with a rubber blade, minus the chatter.
  • CDetailing & glassLifts snow foam and water without the rubber-blade chatter of a window squeegee.
  • DWallpaper & decalsFlattens paste-backed paper and applied graphics without a sheen or a burnished patch.

Vinyl wrap squeegees in blue, red, black and white arranged with a vinyl roll, gloves and install tools

Four colours · one mould

03 — Colour & logo

Colour is a stock decision. The logo is yours.

All four colours come from the same mould, so a mixed carton costs no more than a single-colour one. The logo is printed on the flat face of the card, where it stays readable in a toolbox and does not wear off against the felt.

Blue
Red
Black
White

Chips approximate the moulded colours photographed on this page. Mixed colour cartons are packed to your ratio.

Installer using the felt-edge squeegee to apply blue vinyl wrap film to a car bonnet

In the bay

Where the card actually ends up.

A bonnet pull is the test every installer runs first: long stroke, one direction, felt edge leading. If the edge is dry the film grabs; if it is felt and damp, the air leaves and the film lays down.

Click to enlarge.

04 — Specification

The trade sheet.

Item Felt-edge vinyl squeegee — plastic scraper with fabric felt edge
Size 10 × 7.3 cm
Material Moulded plastic body · black felt edge bonded along one long side
Colours Blue · red · black · white (mixed cartons to your ratio)
Logo Custom logo printed on the card
Grip Two raised ribs on the back face
Use Car vinyl wrap · paint protection film · decals · window film · wallpaper · glass and detailing
Reuse Washable and reusable; felt edge can be brushed clean between jobs
MOQ 1,000 pcs · logo orders confirmed on a pre-production sample
Terms FOB · CFR · CIF · EXW · FCA · DDP · DDU · express
Payment T/T · L/C · PayPal · Western Union · cash
QC Pre-production sample, then final inspection before shipment
Port Tianjin (Xingang) · other Chinese ports on request
Origin Fanjiazhai, Hebei, China

05 — Factory & packing

Moulded, edged and packed on the same site.

The felt is made here, the edge is bonded here, and the cartons are packed here — which is why a colour change and an edge change can happen in the same week rather than across three suppliers.

Bulk cartons of felt-edge squeegees in red, blue and black, poly-bagged and boxed for export
Rolking felt factory buildings, raw fibre bales and felt production lines in Hebei

Left: export cartons and poly-bagged cards. Right: the mill at Fanjiazhai — fibre bales, carding line and finishing.

Framed test reports for the felt and plastic materials: SGS, MSDS, REACH, OEKO-TEX and cGMP

Documents on file

06 — Compliance

The paperwork buyers ask for.

SGS reports, an MSDS, REACH and OEKO-TEX documentation and the cGMP file are held for the materials used in this tool. Current copies travel with the quotation — ask for the ones your market requires rather than the whole set.

Nothing here is a claim about a specific test result; the certificates name the material, the standard and the issue date, and those are the numbers to check against your own compliance file.

07 — Private label

A card with your name on it, in a carton with your barcode.

Stock colours sample in days. After that: your logo on the face, your colour if the volume carries a new mould run, your poly bag, your header card, your carton mark.

  • Logo printed on the card face
  • Four stock colours, mixed cartons
  • Custom colour on volume
  • Poly bag or header card
  • Barcoded export carton
  • Pre-production sample approval
  • Felt edge bonded in-house
  • FOB / CIF / DDP terms

08 — Questions

Before the sample card goes out.

Will the felt edge scratch a wrap or a PPF?

That is what it is for. The felt is softer than the film and carries grit in the fibre rather than pressing it into the surface. Keep the edge clean — brush it out between jobs — because a felt edge loaded with grit behaves like sandpaper whatever it is made of.

Is 10 × 7.3 cm the right size?

It is the size most installers settle on: small enough to reach a mirror base or a door gap, large enough to pull a bonnet in two strokes. If your range needs a different footprint, the mould is the constraint — ask what is already cut before assuming a new one.

How long does the felt last?

It is a wear part, not a permanent edge. In daily bay use expect weeks rather than months; a hobbyist will get a season or more. The card is reusable — the felt is what eventually tells you to replace the tool.

Can it be used wet and dry?

Both. Wet is the normal case for film, where the felt holds slip solution and keeps the edge damp. Dry is fine for decals and wallpaper, where the felt simply spreads pressure without a hard line.

Can I print my logo, and what is the MOQ?

Yes — the logo is printed on the flat face of the card. MOQ is 1,000 pcs, and a logo order is confirmed on a pre-production sample before mass production.

Do you have other squeegees?

Besides this plastic card there is a wool felt squeegee and a felt squeegee with a wooden handle, so a range can be built from three tools rather than one.

What are the delivery and payment terms?

FOB, CFR, CIF, EXW, FCA, DDP, DDU and express. Payment by T/T, L/C, PayPal, Western Union or cash. Tianjin (Xingang) is the nearest port.

How is it packed?

Cards are poly-bagged and packed into export cartons, with the carton mark and barcode to your specification. Mixed colour cartons are packed to the ratio you give us.

Start an order

Send the colour split and the logo file.

Tell us how many of each colour, whether the logo is printed, and where the carton is going — we reply with a price, a sample date and a carton mark.

Rolking Felt · Fanjiazhai, Hebei, China · Factory since 1983 · BSCI audited · SGS tested felt

AppendixFor buyers building a car-accessory range

Pet & animal storage, from the same factory.

This squeegee sits in the car-care aisle. The same mill also cuts and sews felt pet storage for cars, and buyers assembling a full car-accessory programme usually take both: a pet car organizer for the boot, and the fitting tools for the film work that goes with a new vehicle handover.

What the felt line covers

A dog travel organizer and pet storage box for car use in a rigid-panel felt trunk box, with a removable partition: a car boot organizer for dogs on one side and shopping on the other. It folds flat, which is what separates it from a plastic crate that lives in the garage. Stock charcoal, or cut to a vehicle’s boot dimensions.

Around that core box the range extends to a foldable pet storage box, a felt pet storage basket for the house, a cat travel organizer, a puppy travel essentials kit bag, and smaller pieces for leash and toy storage and pet grooming organizer pouches — all from the same felt, bound and stitched on the same floor.

Why it belongs next to this tool

Both products sell to the same buyer: the SUV pet cargo organizer buyer and the installer buying film tools are often the same accessories distributor, and both categories carry the same MOQ logic, the same felt supply and the same export paperwork.

Stock charcoal, cut to a boot drawing, 1,000 pcs per colour — the same MOQ, the same felt and the same export paperwork as the tool above.

See the felt pet trunk organizer →

 


  • Previous:
  • Next:

  • Write your message here and send it to us
    WhatsApp Online Chat !