Anti-slip TPE/PE Garage Floor Mat Waterproof Oil Maintenance Mat to Protect Garage Floor Surface Parking Mats

Short Description:

 

01Two layers, two jobs — absorb the drip, block the concrete

  • The surface takes the hit. A dense needle-felt face wicks oil, coolant, brake fluid and meltwater into the mat instead of letting it pool and travel across the floor, so a single leak does not become a stain the width of the parking bay.
  • The backing is the real barrier. A fully sealed PE/TPE film underneath stops anything that passes the felt from reaching the slab — which matters because oil on bare concrete is not a cleaning problem, it is a permanent one.
  • Nothing creeps under it. The barrier runs edge to edge with no stitched or open border, so fluid cannot track sideways beneath the mat and reappear where you did not look.

02A textured non-slip face that stays put when it gets wet

  • Grip that survives the worst moment. The surface texture gives a wet tyre and a wet boot something to bite on — the exact conditions when a smooth mat becomes a slide hazard at the garage threshold.
  • It stays where you put it. The high-friction backing grips sealed concrete and epoxy floors, so the mat does not walk forward as a car rolls onto it or bunch up under a turning wheel.
  • Safer entry and exit. A stable, matte surface underfoot is a small detail that matters to anyone using the garage as a workshop, a gym or a route into the house through winter.

03Built for the fluids a garage actually produces

  • Oil, brake fluid, coolant, transmission fluid, salt water. The face is designed for workshop chemistry rather than clean water alone, and it does not go tacky, crack or delaminate when something hot or solvent-based lands on it.
  • Reusable, not disposable. Wipe light spills, hose or pressure-wash heavier contamination, hang to dry, and put it back down — a consumable you buy once per season instead of cardboard trays you throw away every month.
  • Kind to the floor underneath. No adhesive, no drilling, no coating. It protects epoxy, sealed concrete, tile and painted floors, and lifts cleanly when you move out or want the floor back.

04Winter is the season it earns its price

  • Snow, slush and road salt stay on the mat. The felt holds meltwater long enough for it to evaporate instead of running across the slab and freezing into a sheet at the door.
  • Stops the salt ring. The white tide line that road salt leaves on concrete is almost impossible to remove once it sets. Catching it in the mat is far cheaper than refinishing the floor.
  • Folds away out of season. Flexible enough to fold or roll for storage, so a winter mat does not become a permanent object in the garage for the other eight months of the year.

05Cut to the bay, sized to the job, branded to your programme

  • Standard sizes plus cut-to-fit. Single-bay, wide-bay and under-car formats, with custom lengths and widths so the mat fits a parking space rather than the other way around.
  • One mat, several uses. Under a daily driver, beneath a project car, in front of a workbench, under a motorcycle or mower, or as a boot and pet area liner — the same roll covers all of them.
  • Private label ready. Custom colour, weight per square metre, edge finishing, printed header cards and retail-ready packing for distributors, detailing brands and automotive retail chains.

Product Detail

Contact US



Anti-Slip TPE Garage Floor Mat | Waterproof Oil Containment Parking Mat — Rolking Felt

Rolking Felt · Garage & workshop · OEM

A garage floor mat with a waterproof TPE back — oil stays on the mat, not in the concrete

A nonwoven top layer that absorbs oil, transmission fluid and drips, bonded to a black TPE backing that stops any of it reaching the slab. Anti-slip on the underside, cut to any size, and dark enough that a working garage never looks dirty.

Nonwoven top
Waterproof TPE back
Anti-slip
Cut to size
Reusable for years

Grey as standard, colour custom · size custom · samples supplied · delivery stated at 7–9 days

2Bonded layers
TPEWaterproof backing
CustomSize in the spec table
7–9 dDelivery stated

Corner of the garage mat peeled back to show the black waterproof TPE layer under the grey nonwoven surface

Surface · backing

01 — Construction

Two layers, and only one of them is meant to get wet.

The upper layer is a nonwoven cloth — it takes the drip, the overspray and the general mess of a working garage. Underneath it, a waterproof TPE film seals the mat, and a non-slip texture on the underside keeps the whole thing where it was laid.

  • ANonwoven surfaceDamp-proof cloth that absorbs and holds liquids instead of letting them run to the floor edge — nonwoven fabric is designed for exactly this: absorbency and liquid repellence in one sheet.
  • BWaterproof TPE filmThe barrier. Nothing that soaks into the top layer gets past it — that is the whole point of the second layer, and a thermoplastic elastomer is chosen for it because it stays flexible and grippy rather than going brittle.
  • CAnti-slip undersideGrips the slab so the mat does not creep when a car is driven onto it or a creeper rolls across it.

02 — The containment test

Pour oil on it. The floor beneath stays dry.

The photograph is the test that matters: oil poured onto the surface pools in the nonwoven layer, and the corner lifted beside it shows the backing — clean, over bare concrete. That is the difference between a mat that hides a stain and a mat that prevents one.

Oil poured onto the mat beside a lifted corner showing the waterproof backing over clean concrete

Containment, not absorption into the slab: liquids stay in the top layer until the mat is cleaned.

03 — Size

Three stock footprints, or your own.

The listing runs three sizes and then says custom, which is the right way round for this product: a single parking bay, a double bay, and a long workshop run are three different cuts of the same mat.

Stock sizes 3 × 6 ft · 7.4 × 8.4 ft · 7.4 × 17 ft
Custom Cut to any size — the mat is easy to trim on site to fit a bay, a bench or an awkward corner
Colour Grey as standard · colour customized
Macro photograph of the rolled garage mat showing the dense nonwoven fibre surface
The garage mat shown flat with two folded mats in front of it

Left: the fibre surface at macro scale. Right: the mat supplied flat — this is a 600 px asset on the listing, so it is displayed inside its native size rather than blown up to fill the column.

04 — Where it goes

Under the bike. Under the creeper.

This is a mat that is judged by what it stops, so the listing photographs it in the places it is actually used: a motorcycle bay, and a work position under a lift. A parking bay is the shot at the top of this page.

Motorcycle parked on the grey garage floor mat
Mechanic lying on the garage mat under a raised car with a wheel nearby

Laid in a garage corner it does the same job under a dog crate or a grooming bench, and in a utility room under a bin store — anywhere a drip would otherwise reach the slab. If that corner is the one you are setting up, we also make felt storage for car boots from the same mill.

Vacuuming the grey garage floor mat in place beneath a classic car

Clean in place

05 — Cleaning

Soap it, hang it, or vacuum it where it lies.

The care instructions on this listing are unusually specific, so they are worth repeating exactly: clean with soap and water and hang to dry, or wet-vac it in place for less downtime. Do not bleach. Regular cleaning is what keeps the mat working rather than just looking grey.

  • ASoap and waterWash, hang dry — the simplest routine and the one that keeps the nonwoven open.
  • BWet vacLifts the liquid out of the fibre without taking the mat out of the bay.
  • CNo bleachStated on the listing. Bleach attacks the fibre and the backing film alike.

New mats can arrive with wrinkles from packing; the listing notes they flatten out with time and use. Lay it on a clean floor and let the weight of the mat do the rest.

06 — Specification

The trade sheet.

Product Felt oil spill garage mat for floors — anti-slip TPE/PE waterproof maintenance mat
Construction Nonwoven cloth top layer + waterproof TPE backing + anti-slip underside
Size 3 × 6 ft · 7.4 × 8.4 ft · 7.4 × 17 ft · customized
Colour Grey or customized (dark shades do not show dirt)
Function Absorbs and contains oils, transmission fluid and workshop liquids; keeps the slab beneath dry and clean
Anti-slip TPE backing textured to hold the mat in place
Cleaning Soap and water, hang dry, or wet vac · do not bleach
Cutting Can be cut to any size on site
Lifespan Durable and reusable for years, per the listing
Sample Supplied on request
Delivery 7–9 days stated on the specification table

Every line above is taken from this product page. Price and MOQ are not published there and are quoted per order.

07 — Questions

Before you measure the bay.

Will it stop oil reaching the concrete?

That is what the second layer is for. The nonwoven top absorbs and holds the liquid; the TPE backing seals it. Nothing passes through the mat, so the slab under it stays as it was laid.

Can I cut it to fit?

Yes — the listing says it is easy to cut to any size. Measure the bay, score and cut from the back so the top surface stays clean, and leave a small margin at a wall so the mat cannot creep.

Will it slide when I drive onto it?

The TPE underside is described as non-slip and is there to keep the mat in place. On a smooth sealed floor, wipe the slab first — dust under the backing is what lets any mat walk.

How do I clean it?

Soap and water then hang dry, or wet vac in place. Do not bleach. Clean it before it is saturated rather than after — a mat that is still holding liquid cannot hold the next one.

It arrived creased. Is that a fault?

No. The listing notes wrinkles from packing that flatten over time. Lay it flat in a warm garage and give it a few days before you judge it.

Which size for a single car?

The three stock footprints are 3 × 6 ft, 7.4 × 8.4 ft and 7.4 × 17 ft. For one car, the smallest is a drip pad under the engine and the middle size is a full parking pad; the long one is a workshop run. Custom is quoted.

Is it only for cars?

No. It is photographed under a golf cart and a motorcycle as well, and the same mat works under a bench, a bin store or a pet crate — anywhere a drip would reach the floor.

What is the delivery position?

7–9 days is stated on the specification table, and samples are supplied on request. Ask for the date in writing with the quotation.

Start an order

Send the bay size and the quantity.

Tell us the footprint, whether you want stock grey or a custom colour, and how many — the quote comes back with a cutting recommendation and a sample date.

Rolking Felt · garage and workshop felt · custom size and colour

 


  • Previous:
  • Next:

  • Write your message here and send it to us
    WhatsApp Online Chat !